Print

Print


*Managing Poinsettia Production through Summer Heat*

Many areas are reporting record high temperatures earlier in the summer
than ever. Poinsettia production during intense summer heat can be a real
challenge.  It can be very difficult to manage the environment and minimize
stress to cuttings in propagation and newly transplanted young plants.
Environmental stresses early in the production cycle can result in poor
branching, deformities in the foliage, and overall reduced plant quality,
that’s why it is so important to manage the environment properly to
mitigate stress.  ****

** **

*Here are some helpful tips to reduce stress to cuttings in propagation: *

**·         **Unpack cuttings immediately upon arrival.  If cuttings can’t
get stuck immediately place in a cooler held at 50-55˚F/10-13˚C. Misting
cuttings will help restore turgidity and hold up better to early stress in
the propagation environment.  Maintain relative humidity at 70% in the
cooler if possible.  If cuttings appear overheated upon arrival notify
supplier immediately! ****

**·         **Only remove the amount of cuttings that can be stuck from the
cooler in one hour. ****

**·         **Have mist ready to go as cuttings are being stuck.  ****

**·         **Maintain relative humidity in the prop environment at near
100%.****

**·         **If possible, reduce night temperatures to 65˚F/18˚C during
the first 5 nights to reduce cutting stress.  Reduced night temperatures
will reduce the incidence of *Erwinia* and help cuttings stand up faster.
****

**·         **Maintain light levels at 1200-1500 ft. candles.  Higher light
will increase the amount of mist needed resulting in leaching, saturated
media, and slow rooting. Higher light will also result in warmer
temperatures!****

**·         **Mist to provide a constant film of moisture to the leaf
surface without over wetting the media.  High heat will increase mist
needed to allow cuttings to remain turgid.   With increased mist botrytis
may be a concern.  Apply a preventative fungicide spray.  ****

**·         **Monitor cuttings closely and adjust mist based on changing
environmental conditions.  Hand mist on the edges of the bench.  ****

**·         **With extreme temperatures misting may continue at night or
more frequently during the day than during propagation when temperatures
are more moderate.  Mist based on the cutting’s needs, not according to a
preset schedule!****

**·         **Wet walkways frequently to increase humidity.   Evaporative
cooling from wetting walkways will also help cool the air temperature. Also,
keep nearby open/unplanted areas wet. Run the booms or mist in empty areas
to keep them cool.****

**·         **Watch for leaf roll. See photo below.  If leaf roll is
apparent cuttings are likely too dry in a hot greenhouse!****

****



*Leaf roll from high light/low humidity****

** **

Establishing rooted cuttings can also be a challenge when extreme heat is
an issue.  Here are some helpful tips to reduce stress to rooted poinsettia
cuttings:****

**·         **Cuttings must be shaded!  Make sure the greenhouse
environment is shaded before cuttings are transplanted and placed in the
greenhouse.  ****

**·         **Light levels initially should be 3,000 ft. candles. If it’s
very hot start at 2000-2500 ft. candles, then gradually increase light
levels.  Once cuttings are established and actively growing light should be
increased to 4,000 ft. candles if possible.  Shade initially to control
greenhouse temperatures also.  Cuttings that have been properly acclimated
to higher light in propagation can handle higher light levels however if
extreme heat is also a problem leaf scorch may occur. ****

**·         **The greenhouse should be nice and humid.  Wet walkways
frequently to provide increased humidity and evaporative cooling.  ****

**·         **Check cuttings frequently.   Syringing several times a day
with cool, clear water will reduce stress.  *Do not use fertilizer when
syringing!   *Apply water only to the base of the cutting and rooting
media, do not water the entire container thoroughly!  Overwatering the
media will result in slow establishing and a risk for increased fungus gnat
pressure.  ****

**·         **Some growers mist newly transplanted cuttings.  This is ok as
long as the mist is managed properly so that the media doesn’t become over
saturated.  ****

**·         **Keep cuttings pot tight.  Pot tight spacing will create a
microclimate around cuttings and increase humidity and decrease airflow.  **
**

**·         **Avoid excess airflow.  If the entire greenhouse is not being
utilized consider hanging temporary plastic which will decrease airflow
around cuttings and create a smaller more manageable space while
environmental conditions are stressful.  ****

** **

Careful and frequent monitoring of the greenhouse environment whether the
cuttings are in propagation or newly transplanted is the first critical
step to minimizing plant stress due to extreme heat.  Watch changing
conditions and react accordingly.  We can’t do anything about the heat but
steps can definitely be taken to reduce stress and ensure that your
poinsettia production gets off to a good start!  ****

                              ****

If you have further questions or concerns you can post those questions in
On Board™ at www.EckeRanchTechHelp.com or email Rebecca Siemonsma at
[log in to unmask]  She can also be reached at 760.944.4060****

** **

** **

**

** **

**
Dr. Teri Hamlin
North Region Agriculture Education
Georgia Department of Education
204C Four Towers University of Georgia
Athens, Ga 30602
706-552-4461 / 706-540-0032
[log in to unmask]